November 21, 2026 · Buyer's Guide

Aluminum Sheet Import Duty 2026: Section 232, Anti-Dumping and CBAM in One Stack

The FOB price of an aluminum sheet stopped being its cost years ago. In 2026 the same tonne carries a 7.5% EU duty, a 14.3–24.6% anti-dumping duty if it is Chinese flat product, a carbon bill priced at €82.32 per tonne of CO2, and a 50% Section 232 duty if it enters the United States. This is the aluminum sheet import duty stack, line by line, with the arithmetic shown.

An importer in Gdansk sent me a landed cost sheet last week and asked why his 5052 coil came in 61% above the FOB price.

Nothing had gone wrong. Three charges had simply arrived at once: the EU anti-dumping duty that has run since 2022, the carbon certificates that started on 1 January 2026, and a Chinese export price that is 13% higher than in 2024 because the export rebate ended.

The metal was never the expensive part. The paperwork around it was.

Start with the code, not the price

Every figure below depends on the ten-digit line, not on the trade name. Sheet and plate above 0.2 mm sit in 7606. Below 0.2 mm you are in foil, chapter 7607.

Inside 7606 the split is 7606.11 for non-alloy and 7606.12 for alloy. Your 5052 and 6061 sheet is 7606.12, and that is the line most anti-dumping and carbon rules are written against.

ProductEU CN codeUS HTSUS lineWhat decides the rate
Non-alloy sheet and plate, over 0.2 mm7606 117606.11Aluminium content, temper
Alloy sheet and plate, over 0.2 mm7606 127606.12.30, MFN 3%Alloy, thickness, origin
Tube and pipe7608 10 / 7608 207608.10 / 7608.20Seamless or extruded, alloy
Foil, 0.2 mm and thinner7607 11 / 7607 197607.11 / 7607.19Thickness, backing

Two neighbouring codes can carry completely different treatment. The EU anti-dumping measure on Chinese aluminium covers flat-rolled product: coil, cut-to-length sheet, circles and plate. Extruded tube under 7608, which we supply alongside sheet and plate, is outside that measure.

That distinction is worth checking before you assume every aluminum product from China carries the same duty. It is also why a buyer who only compares FOB per tonne between sheet and tube is comparing two different legal situations.

China side: the 13% rebate ended in December 2024

On 15 November 2024 the Ministry of Finance announced the export tax rebate on aluminium semis would stop. It stopped on 1 December 2024, and plate, sheet, strip and foil lost the 13% rebate.

SMM measured the effect at about $397 per tonne on plate and sheet, against an average export price of $3,053 per tonne that October. The increase was larger than most mills' export margin, so part of it went into processing fees and the rest into the FOB price over the following quarters.

Two years later that $397 is simply the base. If you compare a 2024 quote with a 2026 quote, split the metal price and the processing fee before you conclude that mills raised prices. The rebate change and a mill increase look identical on a single FOB number.

Europe: 7.5%, then anti-dumping, then carbon

Europe charges in three separate steps, and each one has its own legal basis.

First the third-country duty. For 7606 12 rectangular alloy sheet and plate the TARIC rate is 7.5% erga omnes.

Second, anti-dumping. Definitive duties of 14.3% to 24.6% apply to aluminium flat-rolled products from China, in force since 11 July 2022. The five-year measure reached expiry and the Commission opened a review on 9 October 2026, so the duties continue while that review runs.

Third, carbon. CBAM has applied to aluminium since 1 January 2026. Importers above 50 tonnes a year need authorised declarant status, buy certificates and surrender them against embedded emissions. The certificate price follows the EU ETS auction average: €75.36 for Q1 2026, €75.28 for Q2, €82.32 for Q3. Prices are quarterly in 2026 and weekly from 2027, with the first declaration due by 30 September 2027.

The carbon line is the one missing from most spreadsheets. Take 10 tonnes of CO2 per tonne of metal as a round number for the arithmetic. On a 20-tonne container that is 200 certificates, or €16,464 at the Q3 price — €823 for every tonne of metal.

If your mill can document 8 tonnes instead, you save €165 a tonne, which is €3,300 on that container. That is the whole reason the emissions data request belongs in the enquiry and not in a follow-up mail after shipment.

United States: 3% MFN plus 50% Section 232

The US column 1 general rate on 7606.12.30 is 3%. On top of it sits the Section 232 aluminium duty, which the 2026 revision sets at 50% for plate and sheet. List (i) of US note 16(c) covers 7601 and 7604 to 7609, so 7606 is squarely inside.

Since 6 April 2026 that duty is charged on the full customs value of the goods, not on the value of the aluminium inside them, under Proclamation 11021. Clause 9 also stops a good being charged twice when it appears on more than one metal list.

A free trade agreement does not remove it. Note 16(b) keeps the metals duty in force on top of any preference rate, which surprises importers who assume USMCA or KORUS changes the answer.

Chinese origin also carries Section 301 and the IEEPA layers. Ask your broker to price the actual entry instead of adding percentages from a blog, including this one.

One container, two destinations

Here is the aluminum sheet import duty stack on a 20-tonne container of 5052 H32 sheet, assuming an FOB of $3,300 per tonne. Change the FOB to your own quote; the percentages are what matter.

ChargeEU, China originUS, China origin
Third-country or MFN duty7.5% = $248/t3% = $99/t
Anti-dumping14.3–24.6% = $472–812/tCase by case, not automatic
Section 232—50% = $1,650/t
Carbon, at 10 t CO2e/t€823 = $889/t—
Added cost$1,609–1,949/t$1,749/t plus 301 and IEEPA
As a share of FOB49–59%53% and up

Anti-dumping duty is assessed on the CIF value and the carbon figure uses a euro rate of about 1.08 dollars. I have kept everything on one FOB base so the ratio stays readable, not to produce a number you can put in a contract.

The point is the ratio. On alloy sheet from China, duty and carbon now come to roughly half the metal price in both markets. A 3% move from a mill is noise next to that.

What actually lowers the bill

Origin first. Non-Chinese flat product avoids the EU anti-dumping duty, but it does not avoid the 7.5% duty or CBAM. Compare the total, not the anti-dumping line on its own.

Verified emissions second. CBAM default values carry a mark-up of 10% in 2026, 20% in 2027 and 30% in 2028. Mill-specific data beats the default twice: no mark-up and usually a lower intensity. Ask for direct and indirect emissions per tonne, the installation ID and the production route.

Product form third. A 6 mm sheet and a 6.5 mm plate can sit on different lines with different treatment, and tube under 7608 is outside the flat-rolled anti-dumping measure. Worth five minutes with your customs broker before the enquiry goes out.

Incoterm last, but not least. On DDP the seller pays the duty. On CIF the importer does. In a year when duty is half the metal price, the Incoterm is a price term, not a formality.

What to put in the purchase contract

Agree the code in writing, with the mill's own classification, and name it in the contract. Codes argued about after the vessel sails are expensive.

Ask for the mill test certificate to EN 10204 3.1, the certificate of origin, and an emissions sheet with installation ID, route and t CO2e per tonne for direct and indirect emissions. Your declarant needs those three fields, not a sustainability brochure.

Then settle two commercial questions before price: who is the importer of record, and who buys the CBAM certificates. Add a duty-change clause, because measures changed three times in the last two years and the next review is already open.

If you are pricing aluminum sheet, plate or tube from China, send the grade, thickness and destination port with the enquiry. We will quote the FOB and mark the duty lines that fall on your side.

Frequently Asked Questions

What is the import duty on aluminum sheet in 2026?

Start with the MFN rate: 7.5% for 7606 12 sheet and plate into the EU, 3% for 7606.12.30 into the US. Then add the trade measures that apply to your origin. For Chinese flat product in the EU that means 14.3–24.6% anti-dumping plus CBAM certificates; for the US it means the 50% Section 232 duty and, for China, Section 301 and IEEPA as well.

Does Section 232 apply to aluminum plate and sheet?

Yes. List (i) of US note 16(c) covers 7601 and 7604 to 7609, which includes plate, sheet, strip, foil and tube. From 6 April 2026 the duty is 50% of the full customs value of the goods, not of the aluminium content, and a free trade agreement does not remove it.

Is Chinese aluminum sheet subject to anti-dumping duty in the EU?

Yes, for flat-rolled product: coil, cut-to-length sheet, circles and plate. Duties of 14.3% to 24.6% have applied since 11 July 2022. The Commission opened an expiry review on 9 October 2026, so the duties stay in place while the review is carried out. Extruded tube under 7608 is outside this particular measure.

Is aluminum covered by CBAM?

Yes, from 1 January 2026. Importers above 50 tonnes a year must hold authorised declarant status and surrender certificates against embedded emissions. The Q3 2026 certificate price is €82.32 per tonne of CO2, and the first declaration covering 2026 imports is due by 30 September 2027.

Can I lower the duty by changing the HS code?

No. Misclassification is a penalty risk and customs audits the chapter 76 lines closely. What you can do is make sure the code is right: 7606.11 versus 7606.12, 7606 versus 7608, and the exact thickness matter for both duty and carbon scope. Getting the code right is compliance; changing it to pay less is fraud.

Why did Chinese aluminum sheet get more expensive after 2024?

The 13% export VAT rebate on aluminium semis was cancelled with effect from 1 December 2024. SMM put the cost impact at about $397 per tonne on plate and sheet, against an October 2024 export price of $3,053 per tonne. That increase sits in the FOB price now, so it shows up in every quote even when the mill has not changed its processing fee.

Related Articles

Written by David Chen, Sales Engineer at FANY LASER. Connect on LinkedIn if you want a second pair of eyes on a landed cost sheet. Send the code, the origin and the destination port and we will tell you which duty lines actually apply before you commit to the order.

Sources: Commission Implementing Regulation (EU) 2025/2621 (CBAM default values, applicable from 1 January 2026, revision due by December 2027, mark-ups of 10%, 20% and 30% for 2026, 2027 and 2028); Regulation (EU) 2023/956 (CBAM scope, aluminium goods); European Commission, CBAM definitive regime and price of CBAM certificates (Q1 2026 €75.36 published 7 April 2026, Q2 €75.28 published 6 July 2026, Q3 €82.32 published 5 October 2026, quarterly averaging in 2026 and weekly from 2027, certificate sales on the common central platform from February 2027, first declaration due 30 September 2027); Regulation (EU) 2025/2083 (single mass-based de minimis threshold of 50 tonnes); European Commission news, 11 October 2021, definitive anti-dumping measures on flat-rolled aluminium products from China, duties 14.3% to 24.6%, applied from 11 July 2022; OJ C/2026/5183, 9 October 2026, notice of initiation of an expiry review of those measures; TARIC 7606 12, third-country duty 7.5% erga omnes (read 21 November 2026); HTSUS 2026 Revision 22, chapter 99 note 16(c), heading 9903.82.02, and Proclamation 11021 of 2 April 2026 (91 FR 18201) applying the metals duty to the full customs value for goods entered from 6 April 2026; HTSUS 7606.12.30 column 1 general rate 3%; Ministry of Finance of China, Announcement on Adjusting the Export Tax Rebate Policy, 15 November 2024, effective 1 December 2024; SMM, 2 December 2024 (13% rebate cancellation, about $397 per tonne on plate and sheet, October 2024 average export price $3,053 per tonne). Rates and measures change; the duty owed is the one your customs broker enters on the declaration. This article is not legal or customs advice.