November 19, 2026 · Buyer's Guide

CBAM Stainless Steel 2026: The Per-Tonne Cost EU Importers Now Carry

Since 1 January 2026 an EU importer of stainless steel pays for the carbon inside the metal, not just the metal. The default value for 304 sheet is 3.630 t CO2e per tonne with this year's mark-up. At the Q3 2026 certificate price of €82.32 that is €299 of carbon value on a tonne that sells for about $2,100. The bill is real, and it grows every year until 2034.

A buyer in Rotterdam sent me his first CBAM declaration draft last week and asked whether the number looked right.

His declarant had put 3.63 t CO2e per tonne on 40 tonnes of 304 2B coil. That is the published default value, so the number was not wrong. It was just expensive, and nobody had asked us for the mill data that would have lowered it.

That is the pattern I see on almost every stainless enquiry now. The importer knows CBAM exists, the mill has never been asked for emissions data, and the gap gets filled with a default value the buyer pays for twice: once through the mark-up, and again because a default assumes a dirtier route than many Chinese mills actually run.

This article walks through what CBAM stainless steel costs per tonne in 2026, which codes are covered, who is exempt, and what to ask your supplier before the next container. Numbers are from the EU regulations and from this week's Chinese spot market, with sources at the bottom.

What Changed on 1 January 2026

The transitional period is over. From 2026 the mechanism stops being a report and becomes a payment: authorised declarants buy CBAM certificates and surrender them against the embedded emissions of the goods they import.

The first declaration covers imports made during 2026 and is due by 30 September 2027. Certificates go on sale on the common central platform from February 2027. Nobody pays in 2026 itself, which is why the subject still feels theoretical to a lot of buyers.

It stops feeling theoretical the first time you price a 2030 order.

Which Stainless Goods Are in Scope

All the stainless flat products and long products are covered, plus stainless tube and fittings. Chapter 84 and 85 machinery is not, which catches people out in both directions.

CN codeWhat it covers2026 default, incl. 10% mark-up (t CO2e/t)
7219Flat-rolled stainless, width ≥ 600 mm, hot or cold rolled3.630
7220Flat-rolled stainless, width < 600 mm (strip)3.630
7221 / 7223Wire rod in coils and stainless wire3.630
7222Bars, rods, angles, shapes and sections3.630
7304 11 / 22 / 24 / 41 / 49Seamless stainless line pipe, drill pipe, casing and tube3.630
7306 40 / 61 10 / 69 10Welded stainless tube, round, square and rectangular3.773 to 3.872 (two routes)
7307 21 to 7307 29Stainless flanges, threaded fittings, butt-weld fittings3.201

Two details matter here. First, welded stainless tube publishes more than one default depending on the production route: 7306 40 20 reads 3.872 on one route and a lower figure on another. If your declarant cannot show which route your material came from, the higher value is the safe assumption, and you pay for it.

Second, the machinery exemption is narrower than it looks. A fiber laser cutting machine is Chapter 8456 and out of scope. The stainless sheet you feed it is in scope. So is a stainless tank under 7309 or a balustrade under 7308, even when it arrives as a finished installation kit.

Three Numbers Decide the Bill

Every CBAM argument I have sat in on came down to the same three figures. Get them straight and the rest is arithmetic.

Number2026 valueSource
Default embedded emissions, 304 flat3.630 t CO2e/tImplementing Reg. (EU) 2025/2621
CBAM certificate priceQ1 €75.36, Q2 €75.28, Q3 €82.32European Commission, published quarterly
Free allocation factor (CBAM factor)97.5%Commission Guidance No. 4

The obligation is not simply emissions multiplied by price. It is embedded emissions minus a free allocation adjustment derived from an EU benchmark for your product, and that adjustment shrinks on a fixed schedule.

In formula form, the surrender per tonne is: embedded emissions − (benchmark × CBAM factor × CSCF). The benchmark and the CSCF come from the free allocation act, not from your mill. Your mill supplies the embedded emissions and the activity data behind them.

The Commission's own worked example makes it concrete. Carbon steel rails imported in 2027 with actual emissions of 1.539 t CO2e/t, minus an adjusted free allocation of 1.198 t CO2e/t, left 0.341 t CO2e/t to surrender per tonne. That is the shape of every calculation, stainless included.

Now the part that decides your future cost more than anything else. The CBAM factor falls every year:

YearCBAM factorWhat it means for the free allocation deduction
202697.5%Almost the whole benchmark is still deducted
202795.0%Small change, small bill
202890.0%Default values also jump 30% in mark-up
202977.5%First year the bill is hard to ignore
203051.5%Half the deduction is gone
203226.5%Three quarters gone
20340.0%Full embedded emissions, no deduction

Read the last row again. Whatever discount the free allocation gives you in 2026 disappears by 2034. A supplier choice made today on metal price alone is a decision you will still be paying for in a decade.

The 50-Tonne Line

There is a de minimis exemption, and it is wider than most importers expect. If your total imports of iron and steel, aluminium, fertiliser and cement goods do not exceed 50 tonnes net mass in a calendar year, aggregated across all CN codes, CBAM obligations do not apply to you for that year.

The threshold is per importer and per year, and it is declared in the customs declaration. Cross it once and the exemption is gone for the whole year, including the tonnes imported before you crossed.

Fifty tonnes of stainless is two containers of coil. A kitchen equipment factory buying four containers a year is over the line. A service centre sampling ten tonnes of 316L plate is not.

Do not plan around this line. It sits in a regulation that has already been amended once, it is reviewed as part of the scope extension debate, and 50 tonnes is small once you add aluminium extrusions to the same total.

Default Values Cost You Twice

The published default for stainless is a single figure for a whole product family. It has to be, because the regulator cannot know which mill, which scrap ratio and which electricity grid made your coil.

Two mechanisms make that crude figure expensive. The first is the mark-up: 10% in 2026, 20% in 2027, 30% from 2028. The second is the average itself. Stainless made from a high scrap ratio is far cleaner than the average assumption.

The industry figures show the spread. Worldstainless reports stainless emissions around 0.80 t CO2e/t for Scope 1 and 2 combined on a scrap-based route, with Scope 3 taking the total to about 3.70 t CO2e/t at 50% scrap and about 2.45 t CO2e/t at 75% scrap.

Compare that with the 3.630 t CO2e/t default you are charged in 2026. A mill running a high scrap ratio and a clean grid can be a third below the default. A mill running nickel pig iron and coal power can be above it, and would rather you never asked.

That is the whole commercial argument for asking. Verified actual data is not paperwork for its own sake. On a 25-tonne container it is the difference between two very different invoices, and the difference widens every year as the free allocation shrinks.

A Worked Example on One Container

Take 25 tonnes of 304 2B coil, 1.0 mm, our most common stainless export line, and run the numbers at the Q3 2026 certificate price.

Caset CO2e per tonneCarbon value per tonnePer 25 t container
2026 default, no actual data3.630€299€7,470
Verified actual, 50% scrap route3.70€305€7,620
Verified actual, 75% scrap route2.45€202€5,060

Those figures are the value of the embedded emissions, not your final invoice. Your declarant still deducts the benchmark-based free allocation, which in 2026 removes most of it. I am showing the gross number because that is the number the deduction is subtracted from, and by 2034 it is the number you pay.

One more thing the table shows: actual data can go either way. If your mill's verified figure is above the default, you still have to declare it. That is why the emissions question belongs in the enquiry, before price is agreed, not in the week the vessel sails.

Where the Carbon Bill Sits Against the Metal Price

Chinese stainless spot prices this week give the carbon number a sense of scale. On 18 November 2026, TISCO 304 2B 2.0 mm cut-edge coil was assessed at ¥14,800/t in Wuxi, Hongwang 304 2B 2.0 mm at ¥14,300/t, 430 2B 2.0 mm at ¥7,650/t and 201J2 2.0 mm at ¥7,800/t. Nickel plate rose to ¥123,950/t, up ¥2,600 on the day.

Mysteel's weekly survey put 304 2B Hongwang 2 × 1240 mm at ¥14,200/t, or about $2,129/t including 13% VAT, flat over 5–11 November after the previous week's rally.

So the 2026 gross carbon value of €299 per tonne is roughly 14% of the metal price. Not fatal this year. But look at the direction: the metal price moves with nickel, while the carbon charge only moves one way, because the deduction behind it is being phased out on a published schedule.

For a buyer choosing between 304 and 430 for a non-corrosive indoor part, or between 201 and 304 for a handrail, carbon now belongs in the comparison. 430 carries no nickel premium and a lower alloy cost, and the carbon arithmetic follows the same route logic rather than the grade name.

What to Ask Your Mill Before the Next Order

I have started sending five questions with every stainless quotation. None of them is difficult for a serious mill, and the answers change the declared number.

  1. Verified embedded emissions per tonne, direct and indirect, for this specific product. Not a corporate average, not an EPD for a different plant. The installation and the production route must be named.
  2. The scrap ratio and the electricity source. These two inputs explain most of the gap between a 2.45 and a 3.70 figure, and they are the first thing a verifier asks about.
  3. Which CN code and which production route the mill declares. For welded tube, the route determines whether the default is 3.773 or 3.872. Get it wrong and you pay the higher one.
  4. Whether the data is third-party verified, and to which standard. Unverified numbers are still usable in some cases, but they carry risk if the declaration is audited.
  5. Commitment to supply the same data set with every shipment for the next three years. CBAM is annual, and a one-off letter will not cover the 2028 declaration.

When you compare stainless suppliers, put those five items in the enquiry next to the tolerance and the finish. A mill that answers in a week is set up for this. A mill that sends a brochure is telling you who pays the mark-up.

The product side of the same conversation is on our stainless steel plate, coil and tube page, including the grade range and the finishes we ship.

The Timeline I Would Work To

If you import stainless into the EU and you are above the 50-tonne line, this is the order I would do things in.

  1. Now: apply for authorised declarant status if you have not already. The first declaration for 2026 imports is due 30 September 2027, and it is not a form you fill in during a quiet afternoon.
  2. This quarter: collect installation-level data from every stainless supplier, including the ones you only buy from twice a year. A missing supplier becomes a default value become a cost.
  3. Before February 2027: open the certificate account and understand the purchase mechanics. Sales start on the central platform in February 2027, and the Q4 2026 price is published on 4 January 2027.
  4. During 2027: run one full sample declaration against real supplier data and compare it with a default-value calculation. The gap is your negotiating position for the 2028 contracts.

I am a supplier, not your declarant, and this article is not legal advice. The declaration is signed by the importer, so the numbers that matter are the ones your declarant accepts. What I can do is make sure the mill-side data is ready before you need it.

Frequently Asked Questions

Does CBAM apply to stainless steel?

Yes. Stainless flat products under CN 7219 and 7220, long products under 7221 to 7223, seamless tube under 7304 and welded tube under 7306 are all in Annex I of Regulation (EU) 2023/956. Stainless fittings under 7307 are in scope as well. Chapter 84 and 85 machinery is not, so a laser machine is out while the stainless sheet it cuts is in. See the stainless steel product range for the codes we ship most often.

How much does CBAM stainless steel cost per tonne in 2026?

The default value for stainless flat products is 3.630 t CO2e per tonne including the 10% mark-up for 2026. At the Q3 2026 certificate price of €82.32 that is €299 per tonne of embedded emissions. What you actually surrender is lower, because the declarant deducts the benchmark-based free allocation, and the CBAM factor for 2026 is still 97.5%.

When do I have to pay?

Not in 2026. Certificates go on sale on the common central platform from February 2027, and the declaration for imports made during 2026 is due by 30 September 2027. Certificate prices are published quarterly during 2026 and weekly from 2027 onwards.

Is there a small importer exemption?

Yes. Importers whose total iron and steel, aluminium, fertiliser and cement imports stay at or below 50 tonnes net mass in a calendar year are exempt for that year. The threshold is per importer, aggregated across all CN codes, and it is declared in the customs declaration. Above it, all the obligations apply to the whole year's imports.

Can I keep using default values instead of asking my mill?

You can, and for 2026 to 2028 they come with a 10%, 20% and 30% mark-up respectively. The Commission must revise the default values by December 2027, so the figures in this article will change. Defaults also assume an average route, which is usually worse than a scrap-based mill's actual figure, so relying on them tends to cost more than the data collection does.

Does CBAM replace anti-dumping duty on stainless?

No. They are separate instruments. Anti-dumping measures apply to specific product categories and origins and are collected at customs. CBAM is a carbon obligation collected through certificates, and it applies to every origin. Check both when you build the landed cost, and check the CN code twice, because the two regimes do not use the same product boundaries.

Who has to prove the emissions: the mill or the importer?

The importer is the authorised declarant, so the legal responsibility sits with the importer. The evidence comes from the installation that made the goods. In practice the mill supplies activity data and emissions per tonne, the declarant converts it into embedded emissions for the specific goods, and a verifier checks the chain. That is why the data request belongs in the purchase contract, not in a follow-up email after shipment.

Related Articles

Written by David Chen, Sales Engineer at FANY LASER. Connect on LinkedIn for stainless grade questions, mill data and import paperwork. If a CBAM declaration is due and your supplier has never sent emissions data, send us the CN code, the grade and the tonnage and we will come back with the installation data your declarant asks for.

Sources: Regulation (EU) 2023/956 (CBAM, Annex I product scope); Commission Implementing Regulation (EU) 2025/2621 (default values including mark-ups, applicable from 1 January 2026, revision due by December 2027) — stainless flat-rolled 3.300 t CO2e/t direct, 3.630 / 3.960 / 4.290 with the 2026 / 2027 / 2028 mark-ups, welded stainless tube 7306 40 and 7306 61 10 at 3.520 and 3.430 by production route, stainless fittings 7307 21 to 7307 29 at 2.910; Commission Guidance No. 4 on the free allocation adjustment (CBAM factor 97.5% in 2026, 95% 2027, 90% 2028, 77.5% 2029, 51.5% 2030, 39% 2031, 26.5% 2032, 14% 2033, 0% 2034); Commission Guidance No. 5d, iron and steel sector guidance (worked example: carbon steel rails, 2027, 1.539 t CO2e/t actual less 1.198 t CO2e/t adjusted free allocation); Regulation (EU) 2025/2083 (single mass-based de minimis threshold of 50 tonnes, new Article 2a and Annex VII); European Commission, price of CBAM certificates (Q1 2026 €75.36 published 7 April 2026, Q2 €75.28 published 6 July 2026, Q3 €82.32 published 5 October 2026, Q4 to be published 4 January 2027; certificate sales on the common central platform from February 2027); worldstainless CO2 emissions report 2024 (stainless Scope 1+2 around 0.80 t CO2e/t on a scrap-based route, total around 3.70 t CO2e/t at 50% scrap and 2.45 t CO2e/t at 75% scrap); Mysteel weekly stainless survey, 12 November 2026 (304 2B Hongwang 2 x 1240 mm at CNY 14,200/t, about $2,129/t including 13% VAT); Chinese spot assessments for 18 November 2026 (TISCO 304 2B 2.0 mm cut-edge CNY 14,800/t, Hongwang 304 2B 2.0 mm CNY 14,300/t, 430 2B 2.0 mm CNY 7,650/t, 201J2 2.0 mm CNY 7,800/t, nickel plate CNY 123,950/t). Carbon values in this article are our own arithmetic on those published figures, not a quotation. Not legal or customs advice — the declaration is signed by the importer's authorised declarant.